Skip to content

Print straight to your Rollo on a Mac (beta)

Send each label straight to a USB Rollo, skipping its driver, and know what the print queue tells you when a label may not have printed.

Last updated Oct 30, 2026 · Applies to NotBot 1.4.9+

With Print straight to your Rollo on, NotBot sends each label straight to your Rollo over USB, skipping the Rollo driver. Labels come out the same on every computer and always on the right size. A Rollo with no driver installed works too. With it off, labels go through the Rollo driver as before.

It is in beta, on a Mac only, and off until you turn it on for your Rollo. On Windows, Rollo labels print through the driver as before.

  • NotBot runs on a Mac.
  • Your Rollo is plugged into the Mac with a USB cable and turned on. The Rollo driver is optional.

In the purple bar at the top of NotBot, click Customize, then Advanced Settings. In the list of pages on the left, under PRINTING, click Printers & routing.

Under Your printers, click your Rollo. When NotBot recognizes it as a Rollo, a Print straight to your Rollo section marked Beta shows under the printer list. Other printers never show it.

A Rollo with no driver on this Mac is listed as Rollo (USB). Labels for it do not print until you turn this on.

  • Rollo with its driver installed: pick Straight to Rollo instead of Rollo driver.
  • Rollo (USB), no driver: turn on the switch.

The same switch is on Advanced Settings › Basics under Printer when your default printer is a Rollo, and in the printer step of the setup wizard. There it says On. Printing straight to your Rollo. with the driver installed, or Connected over USB, no driver needed. without one.

The choice is saved for that Rollo. Switching back to Rollo driver keeps every setting below.

On the right of the section, NotBot shows Your default label, dot for dot: exactly what the Rollo prints for your default label. Click Print a test label. NotBot says Test label sent., or Still waiting on the printer. Check the Print Queue before printing another., or why it did not print.

With it on, the section has every control the Rollo driver has. The next label uses whatever is set, and the preview follows each change.

Setting Default What it does
Darkness 8 0 to 15.
Speed 6 in/s 1 to 8 inches a second.
Logo shading Normal Draft, Normal or High. Text is always sharp.
Slow down for dark labels On Mostly black labels print lighter and slower so they come out solid.
Left / right, Up / down 0 mm Moves the print, −20 to 20 mm. Minus moves it left or up.
Tear-off stop 0 mm Where each label stops after printing, −20 to 20 mm.
Rotate None None, 90°, 180°, upside down or 270°. A quarter turn shrinks the design to fit.
Roll type Gap Gap for die-cut labels, Continuous for a plain roll, Black line for marks on the back.
Dotted line between labels Off On or off.

Once you change any of them, Reset to Rollo defaults puts them all back.

NotBot never loses a Rollo label without saying so, and it never reprints one on its own. Under each label in Recent Labels, the print queue says whether the label can have printed and what to do. Tap a label to reprint it.

What Recent Labels says What it means
May have printed: check the Rollo before reprinting. The label may have reached the Rollo. Look at the Rollo before you reprint, so the buyer does not get two.
The Rollo did not confirm this label: check it before reprinting. NotBot sent it, but the Rollo never confirmed it printed.
NotBot closed while this label was printing: check the Rollo before reprinting. NotBot closed partway through this label.
Not sent: and a reason, for example Not sent: the Rollo is unplugged. Nothing reached the Rollo, so it cannot have printed.
Waiting: and a reason, for example Waiting: the Rollo is out of labels. It prints as soon as the Rollo is ready. The label never reached the Rollo and prints by itself once the Rollo is ready.

The reasons name what NotBot saw: the Rollo is unplugged, out of labels, its lid is open, it has a paper jam, it is paused, it reports an error, it stopped responding, or another app was using it.

NotBot also tells you at the moment it happens. When a label may not have printed, a message says A label sent to Rollo (USB) may not have printed. Check the printer, and reprint it from Recent Labels only if it is missing. When the Rollo needs you (out of labels, lid open), a Check your Rollo message names the problem and ends Labels resume once it is fixed. With a driver installed, the messages use your Rollo’s own name instead of Rollo (USB).

See Print queue for every status a label can have.

The section says NotBot cannot see this Rollo right now.

The Rollo is unplugged or turned off, so its labels wait for it. Plug it back in and turn it on. If the Rollo’s driver is installed, you can also switch to Rollo driver to print them through the driver. A Rollo (USB) with no driver prints only straight to the Rollo, so leave the switch on and plug it back in.

It says printing straight to the Rollo kept failing.

After repeated failures NotBot stops printing straight to that Rollo until it restarts. With the driver installed, its labels print through the Rollo driver meanwhile; switch to Rollo driver and back to try again. A Rollo (USB) with no driver has no other way to print, so its labels fail until you check the Rollo and turn the switch off and on, or restart NotBot. The message that tells you has a Use printer queue button when the Rollo has a driver: it puts that Rollo back on the driver.

It says Not available for this connection yet.

Printing straight to the Rollo works over USB only. Labels print through the Rollo driver.

I do not see Print straight to your Rollo at all.

It shows only on a Mac, only for a Rollo plugged in by USB, and only once NotBot recognizes it. Click Refresh printer list at the bottom of Your printers, and check the cable and the power.